top of page

INSTRUMENTATION · OUTDOOR EQUIPMENT · IoT SENSORS

Overmolding and cable assemblies for instrumentation and IoT

Instruments and sensors built to live outdoors in rain, road salt and frost — overmolded in Canada, with no enclosure and no hand-poured epoxy.

River monitoring station in winter, with an overmolded sensor at the end of an arm over the water

PROTOTYPES

No minimum order

TOOLING

Low-cost molds

SEALING

IP67/IP68 depending on design

MANUFACTURING

In Canada

01

Your requirements, our commitments

Your electronics work where no one is watching. Four commitments guide every part we deliver:

Sealing

No gasket or cable exit for moisture to get through.

Vibration resistance

Components, solder joints and wires are locked in the resin, so nothing moves or fatigues under vibration.

Service life

Protection designed for an instrument you install and never open again.

Compact size

A sealed sensor with no enclosure, where space is tight.

02

How Fillio delivers

Low-pressure overmolding

Electronics are encapsulated in a heat-molded resin, with no voids and the same finish on every part. An alternative to hand-poured epoxy.

Cable assemblies and harnesses

Built and 100% tested to IPC/WHMA-A-620, with sealed Deutsch, M8 or M12 connectors.

Mechanical design

Geometry and mold adapted to your product, at low tooling cost.

From prototype to production

No minimum order — a single part if that's what it takes to validate. Traceability per part or per lot on request.

Overmolded electronic module mounted on a DIN rail in an electrical panel, between terminal blocks

03 — MEASUREMENT AND PROTECTION INSTRUMENTS

Install it, then forget it.

Detectors, protection relays, measuring instruments: they must run for years without maintenance, with the same quality from one lot to the next.

—

Overmolded joints and cable exits, with no gasket to monitor.

—

Documented, 100% tested harnesses.

—

Traceability for every part produced.

04 — OUTDOOR CONNECTED EQUIPMENT

Outdoors, winter puts every connection to the test.

Signage, stations and roadside equipment live in rain, de-icing salt and frost, with transport vibration on top.

—

Electronics and cable exits overmolded as a single block.

—

100% tested harnesses, ready to install.

—

Cable exits reinforced against pull-out and rough handling in operation.

Solar-powered roadside monitoring trailer on a highway shoulder in winter, with an overmolded sensor on the mast
Overmolded IoT sensor mounted on a post in a dairy barn

05 — IoT AND AGTECH SENSORS

A sealed sensor with no room for an enclosure.

In a field, a greenhouse or a barn, the sensor lives with humidity and dust, often far from everything. It has to keep working without anyone going back to it.

—

The same part from one sensor to the next, from the first prototype to full deployment.

—

IP67 or IP68 depending on design.

—

Cable or connector overmolded directly onto the sensor: no cable gland or seal to design in.

06

Standards and environments

REQUIREMENT

WHAT FILLIO APPLIES

Sealing

IP67 or IP68, depending on geometry and material

Materials

UL94-rated polymers, RoHS-compliant components

Harness workmanship

Procedures per IPC/WHMA-A-620, 100% tested

Connectors

Deutsch, M8, M12 and industrial circular

Environments

Rain, salt, frost, dust, condensation and vibration

07 — OUR CLIENTS

Trusted by

Local instrument and equipment manufacturers who rely on us to protect and assemble their products.

Controlab

“Collaborating with Fillio means working hand in hand with a true development partner. […] Their cutting-edge know-how and collaborative approach have enabled us to build, together, a solution perfectly tailored to our needs.”

Yvan Bissonnette, CEO, Controlab

Try it on your sensor.

Still potting epoxy by hand? Send us your sensor or board: we'll propose an overmolded version and a first prototype batch in the size you need.

bottom of page