MEMBER
CADSI
PARTICIPANT
MINERVA Initiative
HARNESSES
Per IPC/WHMA-A-620
MANUFACTURING
In Canada
CANADA IS BUYING CANADIAN
Canada's new Defence Industrial Strategy aims to direct 70% of defence equipment procurement to Canadian companies. For an integrator, every component made in Canada counts toward that target and toward its Industrial and Technological Benefits (ITB) obligations.
01
Your requirements, our commitments
Our connections hold up where your systems are deployed, not just on the test bench. Four commitments guide every part we ship:
Ruggedization
Shock, vibration, moisture, dust and extreme temperatures.
Lot traceability
Which lot, which material and which operator, for every part shipped.
Canadian content
A domestic supplier that counts toward your Industrial and Technological Benefits (ITB) obligations.
IP protection
Drawings and parts that stay in Canada.
02
How Fillio solves it
Low-pressure overmolding
The PCB, sensor or cable-to-connector joint is encapsulated in a polymer injected at low pressure. You get a sealed part (IP67/IP68 depending on design), no enclosure to assemble, and built-in strain relief.
Wire harness and cable assembly
Cut, crimped and 100% tested to IPC/WHMA-A-620, with Deutsch, M8/M12 and industrial circular connectors.
Design for manufacturing
Our team works with yours on geometry and tooling from day one, so the part is right the first time.
One roof in Canada
Design, molds, production and lot documentation, nothing outsourced overseas, which simplifies your compliance with the Export and Import Permits Act.

03 — UAVS (DRONES)
On a drone, every gram counts.
Overmolding replaces the housing, gaskets and screws with a single shell molded directly onto the electronics: less weight, less volume, fewer parts to assemble.
—
Protects onboard electronics from rotor vibration, hard landings, rain and salt spray.
—
Reinforces cable exits, the first failure point on any vehicle that vibrates.
—
Applies equally to civilian inspection drones, often dual-use: same constraints, same requirements.
04 — UNMANNED GROUND VEHICLES (UGV)
On a UGV, the terrain never lets up.
An autonomous ground vehicle crosses mud, snow, water and rough terrain, with power electronics, sensors and harnesses spread across the whole chassis. Every exposed connection is a potential point of failure.
—
Seals exposed connectors and sensors (cameras, lidar, radar) against water, mud, salt and pressure washing.
—
Reinforces harnesses exposed to constant shock and vibration from the terrain.
—
Custom harnesses for modular electrical architectures, from prototype to production, for military vehicles and their civilian versions alike.


05 — DUAL-USE
One technology, two markets.
A system designed for defence often finds a civilian version: inspection, mining, agriculture, public safety. The reverse is just as true. The constraints stay the same: shock, vibration, water, cold.
—
The same mold and the same process serve both versions of your product.
—
Move from one market to the other without qualifying a new supplier.
—
Lot documentation follows the part, wherever it is deployed.
06
Standards and environments
REQUIREMENT
WHAT FILLIO APPLIES
Harness workmanship
Procedures per IPC/WHMA-A-620
Sealing
IP67 or IP68, depending on geometry and material
Materials
UL94-rated polymers, RoHS-compliant components
Traceability
Compliance documents per unit or lot
Environments
High North and Arctic, swamps and mud, coastal and marine environments
In-service support
Molds stored and documentation archived for spare parts
07 — LONG-TERM SUPPORT
Parts available for the full life of your system.
A defence system stays in service for years, sometimes decades. Its connections must be replaceable like-for-like, long after the first lot.
—
Your molds are stored and maintained in-house, ready for a new run.
—
Manufacturing records and lot documentation are archived: the spare part is built to the same parameters as the original.
—
Small replacement runs, even years after initial production.
—
A local, reachable supplier that responds quickly to maintenance and repair requests.

08 — TESTIMONIAL
“We had a critical need, and Fillio met it every step of the way. A team we can count on — it’s hard to ask for anything better.”
— CTO, Canadian national defence supplier
Try it on your part.
Send us a drawing or a sample: we'll propose an overmolding or harness approach and a first prototype lot in whatever quantity you need.
Is your project subject to the Controlled Goods Program or ITAR? Contact us before sending your drawings. We'll confirm the required framework together before any technical data is exchanged.
